S素年錦時
the white part of the arrow point to is too wild,which led to edge of the rubber turned up.
excellentpri
模具专业术语(中英)一,入水:gate 进入位: gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口: switching runner/gate 唧嘴口径: sprue diameter 二,流道: runner 热流道: hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance 热嘴: hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头: connector plug 插座: connector socket 密封/封料: seal 三,运水:water line 喉塞:line lpug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四,模具零件: mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边 L:guide pin 顶针板:ejector retainner plate 托板: support plate 螺丝: screw 管钉:dowel pin 开模槽:ply bar scot 内模管位:core/cavity inter-lock 顶针: ejector pin 司筒:ejector sleeve 司筒针:ejector pin 推板:stripper plate缩呵:movable core,return core core puller 扣机(尼龙拉勾) :nylon latch lock 斜顶:lifter 模胚(架) mold base : 上内模:cavity insert 下内模:core insert 行位(滑块) slide : 镶件:insert 压座/斜鸡:wedge 耐磨板/油板:wedge wear plate 压条 plate 撑头: support pillar 唧嘴: sprue bushing 挡板:stop plate 定位圈:locating ring 锁扣:latch 扣鸡:parting lock set 推杆:push bar 栓打螺丝:S.H.S.B 顶板:eracuretun 活动臂:lever arm 分流锥:spure sperader 水口司:bush 垃圾钉:stop pin 隔片:buffle 弹弓柱:spring rod 弹弓:die spring 中托司:ejector guide bush 中托边:ejector guide pin 镶针:pin 销子:dowel pin 波子弹弓:ball catch 喉塞: pipe plug 锁模块:lock plate 斜顶:angle from pin 斜顶杆:angle ejector rod 尼龙拉勾:parting locks 活动臂:lever arm 复位键,提前回杆:early return bar 气阀:valves 斜导边:angle pin 术语:terms 承压平面平衡:parting surface support balance 模排气:parting line venting回针碰料位:return pin and cavity interference 模总高超出啤机规格:mold base shut hight 顶针碰运水:water line interferes withejector pin 料位出上/下模:part from cavith (core) side 模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件: Do not use (core/cavity) insert 用铍铜做镶件: use beryllium copper insert 初步(正式)模图设计:preliinary (final) mold design 反呵:reverse core 弹弓压缩量:spring compressed length 稳定性好:good stability,stable 强度不够:insufficient rigidity 均匀冷却:even cooling 扣模:sticking 热膨胀:thero expansion 公差:tolorance 铜公(电极) :copper electrode 补充:模具常用英文缩写与其解释
