塑料模具英语

到百度收索 模具专业英语 即可解决。很快的

Pipi cattle through the wrist pad injection mold design, described the design of thermoplastic injection molding methods, the design objective is to use in meeting the conditions required to minimize the complexity of the mold, as well as system Caused by this. Plastic injection mold used for molding thermoplastics, thermosetting plastics in recent years the application of molding parts are becoming increasingly widespread. Pipi cattle under the wrist pad plastic parts forming the structure and work Art analysis, choice of material plastic parts, die structure design process. Mold design, mold manufacturing, mold materials, a reasonable processing technology and modern equipment such as molding molding quality plastic parts is an important condition for One. Plastic parts of the wrist pad for Pipi cattle, requires a certain amount of toughness, anti-skid, wear-resistant properties. This paper describes the design of the injection mold every aspect of the process, which focuses on the gating system design, molding parts, as well as the work of calculating the size of the mold manufacturing process. Gating system, including the mainstream Avenue, Stream Road, gate and other points as well as the cold four parts. Molding parts including the cavity and core, are modular. Combined cavity, core processing to facilitate mold manufacturing, mold can reduce manufacturing costs. Molding Parts of work calculated using the average size of the calculation method, and the wall cavity and floor for strength checking to ensure that the safety performance and mold performance. In addition, most of the mold using a template Market standard template, you can reduce the die manufacturing cycles, lower manufacturing costs. Throughout the design process, in addition to die design using the traditional method, but also skillfully use modern mold design and engineering software graphics software, such as Pro/E4.0, AutoCAD and so on, will not only allow the use of software-based Convenience of intuitive, and can shorten the design cycle. Key words: injection mold; Plastic molding process; molding parts manufacturing process

Mould course

看是哪种类型的模具。塑料类产品的模具一般是mould或者mold。冲压模这类的一般是die。还有有些国家说 toolings也很多。

一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round (full/half runner) 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin 斜顶杆：angle ejector rod 尼龙拉勾：parting locks 活动臂：lever arm 复位键、提前回杆：early return bar 气阀：valves 斜导边：angle pin 术语：terms 承压平面平衡：parting surface support balance 模排气：parting line venting 回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut hight 顶针碰运水：water line interferes withejector pin 料位出上/下模：part from cavith (core) side 模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件： Do not use (core/cavity) insert 用铍铜做镶件： use beryllium copper insert 初步（正式）模图设计：preliinary (final) mold design 反呵：reverse core 弹弓压缩量：spring compressed length 稳定性好：good stability,stable 强度不够：insufficient rigidity 均匀冷却：even cooling 扣模：sticking 热膨胀：thero expansion 公差：tolorance 铜公(电极)：copper electrode