模具英语大全

Mould components & AccessoriesMould base 模胚 Bolts 螺栓Mould frame 模架 screw 螺丝Top clamp plate 面板 Stripper screw 脱料螺丝Bottom clamp plate 底板 F.H.C. screw（flat head cap screw） 平头螺丝 Socket head sountersunk screws 平头螺丝Hot runner plate 热流道板 S.H.C. screw( socket head cap screw) 杯头螺丝Runner plate 水口板 hexagonal socket head cap screw 杯头螺丝A plate A板 Hexagonal head screw 六角头螺丝B plate B板 Grub screw 无头螺丝（等高螺丝，基米螺丝）Stripper plate 推板 Ball screw 波仔螺丝Support plate 支撑板 Shoulder screw 限位螺丝（带肩螺丝，塞打螺丝）Spacer plate 方铁 latch 插销Ejector retainer plate 顶针面板 baffle 隔水片Ejector plate 顶针板 plugs 喉塞Insulating plate 隔热板 Jiffy plugs 喉咀Cavity 前模 o-ring 密封圈Cavity insert 前模镶件 Cooling tube 散热管Core 后模 spring 弹簧Core insert 后模 Support pillar 撑头Slide 行位 Stop pin 垃圾钉Slide insert 行位镶件 Dowel pin 管钉jaw 行位压块 Spacer ring/washer 间隙圈Slide wear plate 行位耐磨块 Venting slots 排气槽Slide guide block 行位导向块 thermocouple 电热偶Slide lock 行位锁/行位扣 Thermocouple connector 接线盒Wedge block 铲机 Limit switch 限位开关W.B. wear plate 铲机耐磨块 probe 探针Core pin 镶针 Pry bar slots 开模槽Angle pin 斜导柱 Safety strap 模锁Angle lifter 斜顶 Lifting eye bolt 吊环（方向已固定）Lifter guide block 斜顶导向块 Hydraulic cylinder 油缸Lifter base 斜顶座 Air cylinder 气缸Press block 模料挤紧块 Hydraulic motor 马达hoist ring 吊环（可转动方向） Knock out hole 顶棍孔 Parting lock 树脂开闭器（尼龙扣）Name plate 铭牌 Straight side interlocks T型锁（直身锁）Date code 日期印 Tapered interlocks 斜度锁Cavity number 模穴号 sensor 感应器engrave 刻字/凹入 heater 加热器Raised out 凸出 K.O. insert 顶棍孔镶件Gate type & runnerDrop gate 点水口 Sprue bushing 唧嘴Pin point gate 细水口 Sprue/gate 浇口Edge/side gate 边水口 Center sprue/sprue gate 中心进胶/直浇口 runner shut off 流道开关/转水口Sub gate 潜水口 Runner lock pin 水口扣针Tunnel gate 隧道浇口 Puller 拉钩Ring gate 环形浇口 Sprue lock pin 拉料杆Fan gate 扇形浇口 Slag well 冷料井Valve gate 针阀式水口 Banana gate 香蕉水口 Guide＆Locating systemGuide pin/leader pin 导柱 Grinder研磨机 Crane 天车（吊车）Guide bushes 导套 Grinding machine 磨床 Groover machine 开槽机locating ring 法兰 Lathe machine 车床 Radial drill摇臂钻床 EGB( ejector guide bush) 中托司 Milling machine 铣床 Wire cut machine 线割机Ejecting systemEjector pin 顶针 Gear 齿轮Stepped ejector pin 有托顶针 Rack 齿条Blade ejector 扁顶针 Bearing 轴承Ejector bar 顶块 Roller bearings 滚珠轴承Sleeve 司筒 Retraction spring 复位弹簧Stripper plate 推板 Return pin 回针Unscrewing 脱螺纹 Two-stage ejector 二次顶出Ejector retainer plate 顶针面板 chain 链条Ejector plate 顶针板 Chain wheel 链轮Stop block 限位块 key 键Ejector bushes 顶针套 Specification of Injection Moulding MachineDiameter of the location ring 法兰直径Nozzle radius 机嘴半径Nozzle injection hole diameter 机嘴注射孔直径Depth for the nozzle into the mould 机嘴进入模具的深度KO hole distance KO孔间距fine thread 细螺纹Rough thread 粗螺纹mould opening distance 开模距离mould thickness 模具厚度tie bar distance Tie Bar 距离Injection defectsflash 披锋 Warpage/deformation 变形Ejected mark 顶白 Step 断差/台阶Weld line 熔接线 Short shots 短胶Sink mark 缩水 Sharp corner 尖角Gas trapped 困气 Sharp edge 尖边Scratch marks 拖花 Air bubble 气泡Kiss off 碰穿 Short shot 短射(欠充填)Shut off 擦穿位 Flow mark 流纹Sticking cavity 粘前模 Sticking core 粘后模 Mould designplastic 胶位 radius 半径Draft angle 拔模角 Diameter 直径Fillet/ inside radius 圆角 Inner diameter/I.D. 内径Outside radius 外转角 Outer diameter/O.D. 外径Sprue bush radius 机嘴球半径 boss 柱位Corner radius 转角半径 Rib 骨位Part drawing 产品图 hole 孔Mould drawing 模图 Pre-hardened steel 预硬钢Plastic material 胶料 Through hardened steel 全硬钢Parting line 分型面 Filling uneven 走胶不平衡Plastic thickness 胶厚 Balanced runner 平衡水口系统Shrinkage rate 缩水率 Cycle time 循环周期 Surface treatmentEDM 火花纹 Demoulding polish 脱模抛光High polish 高抛光 Medium polish 中抛光 Optical/mirror polish 镜面抛光 chrome 镀铬 Texture 蚀纹 我这里是WORD文档，不能直接插入文件，所以直接复制的，如果看不清楚加QQ，我传给你。帐号就是我的用户名。觉得满意记得采纳哦