• 回答数

    4

  • 浏览数

    138

高@设计师
首页 > 英语培训 > 口述英文翻译

4个回答 默认排序
  • 默认排序
  • 按时间排序

原来我在这里8

已采纳

您好,领学网为您解答:口头声明:oral statementoral 英 [ˈɔ:rəl] 美 [ˈɔrəl] adj.口服的;口头的,口述的;属于或关于嘴的;构成或使用言语的 n.(尤指外语考试中的)口试statement 英 [ˈsteɪtmənt] 美 [ ˈstetmənt] n.声明;(思想、观点、文章主题等的)表现;(文字)陈述;结算单 vi.(英国)对儿童进行特殊教育评估认定 vt.申请(小孩)有特殊教育需要例句:口头声明可当作使用商品说明或商标或标志论。An oral statement may amount to the use of a trade description or trade mark or mark.

口述英文翻译

183 评论(14)

巫毒小子

这个视频其实主要讲的是怎么改良一个氢气制取方法。这个人应该还有一个较早的视频讲的是氢气的具体制取方法。那么就先就这个视频来翻译一下。The Hydrogen Generator Cell (Upgrade). We upgraded the plates we use in the cell and solved the water discoloration problem.引言:我们改进了原来的装备目的是要解决水变色的问题。As you saw in the original cell, we had a lot of discoloration in the water. I came to find out that the blades were actually rusting up since they were steel or iron. We are actually gonna make the plates and upgrade the cell out of thick aluminum foil. 介绍(口述):在原先的装备中,我们看到水变色变得很厉害。我发现原因是因为隔片生了锈,因为它是刚或铁做的。这次我们打算用厚的锡纸来制作隔片来改良我们的装备。For the upgrade we need:- Aluminum foil serving tray- Double sided sticky tape- Pair of scissors- 1 Ft of wire需要用具:烤蛋糕用的锡纸托盘, 双面胶带,剪刀,1英尺(大概30厘米)导线Sure you've seen these containers before. And just cut out slits up of this container. Try to find out the straightest part. Use a rolling pin to actually flatten the surface out. I've done so on a huge piece of this right here. I've cut out plates, four plates, in this shape. All of them stack them up, just cut them with scissors, regular kitchen shears woodware. There’s also a slot to cut out just like so on one corner, the other one you actually chop off the corner. And stack them up, put double-sided sticky tape in the middle of them. I used five of them, just as shown on this one. Remove all the protection of the double-sided sticky tape, and put the next plate on, facing the slot the other way from this plate. As we are gonna alternate all the plates... each one... the first one being positive, second one negative, third one positive, and the forth one is going to be negative again. Alright, we're done assembling the plates, and all four plates are separated with the double-sided sticky tape. This time I used three layers of double-sided sticky tape, since we are gonna need more gap, since the plates are bigger. The plate size is 4'' by 2''. Through the slots I bent the tabs out, and then punched a hole with the hole punch. Right through there, we are gonna put our wires through, right over here, this tab and this tab, one’s gonna be positive and one’s gonna be negative. 备注:原文在上面。他比较罗嗦,这里就不一字一句地翻了。主要制作过程如下。找一个烤蛋糕用的锡纸托盘 (超市里应该能买到)。把托盘四周高起来的部分剪掉,留下底面备用。将底面压平。用底面剪出 4 个长方形的平面,长4英寸,宽2英寸 (大约10厘米长,5厘米宽。)参照视频53秒左右。在平面的一角剪一条缝(不要把那个角剪掉),把另外的一个角彻底剪掉。将4个平面都这样做。参照视频1:09分。在一张平面的一面贴上双面胶带。只要少贴几处就行了。然后拿起第二张平面,注意要翻过来再贴到第一张平面上。就是第二张被剪掉的那个角落要和第一张没有被剪掉的角落吻合。然后用同样的方法翻转着把第三和第四张平面也贴在一起。为了能让相邻的平面的间隔距离大一些,每处我都用了三层双面胶带。都贴好后就像视频1:45分一样。注意平面的缺角是每隔一层交替的,即第一和第三层是正极,第二和第四层是负极。像视频1:45分那样,把第一和第三层开缝的那部分折叠到一侧,把第二和第四层开缝的部分折叠到另一侧。在折叠后的小片上打孔,然后把正负极的导线分别连接到每一侧开孔的小片上。即大功告成了!Okay we've got our cell assembled with our new upgraded aluminum foil plate. We’re gonna fire it up and see how it goes. Here we go…See there's much less discoloration with aluminum foil in there and still sufficient amount of hydrogen being produced as you can see in the bubble there. That is a great amount of hydrogen. Alright, we've had our cell running for a few minutes. I’d say about 8 minutes or so. And all you see is hygrogen, no discoloration in the water, no problems at all actually. As you can see I may have to make a new bottle or something, ‘cause this one is losing its form. It’s actually burning a little bit away. But I can make another addition on top, but that’ll be the next upgrade. Tune in for that one. 口述:Okay, 一切就绪。我们测试一下。可以看出水并没有变色,同时生成了大量的氢气。没有丝毫问题。结尾3:25分左右:我得再找一个瓶子,因为这个塑料瓶经高温已经变形了。也许我可以在瓶子的上面加一个保护的装置,不过这个还是留到下一个视频作为下一个改进吧。Hydrogen Generator (Upgrade)Aluminum came out to be a better option and you can still find it around the household. 总结:用锡纸做的装备效果更好,而且锡纸是家居必备品,很容易找到。祝你做得顺利!!! :D 修改更新:楼主,我找到另一个视频,出自同一个人之手,这个视频是你的视频的前作。你看看下面的连接能不能工作,如果连接被封锁的话,我可以下载下来然后发送给你。希望有所帮助!

340 评论(12)

曼妙樱花

当然你见过这些容器。而刚刚剪下缝了这个容器。尝试找出最直的一部分。使用杖实际扁平表面。我已经做到了这一块巨大的权利,使这里。我已经剪下板,四板,在此形成。所有这些堆栈他们,只是他们剪,厨房剪木制品正常。还有一个槽,以切断等,就像一个角落里,还有一个你实际上砍掉的角落。和堆栈他们,把双面就在他们中间胶带。我使用了其中5,正如在这一个表现。删除所有的双面胶带保护,并提出下一盘上,面对这个板的插槽的其他方式。由于我们gonna altern吃所有的板块...每一个...第一个是积极的,消极的第二个,第三个积极的,并提出了一个将是负面的了。好吧,我们就大功告成了组装板,和所有四个板块与双面胶带分开。这一次,我用了3双面胶带,因为我们gonna需要更多的差距,因为层板块更大。板的尺寸为4 2 '' ''。通过插槽我弯下腰的标签内,然后拳打脚踢与打孔器洞。通过有权利,我们gonna把我们的电线,在这里的权利,这个标签,这标签,一个人的gonna是积极的,一个人的gonna是否定的

144 评论(13)

晓布丁2011

Oral input

139 评论(14)

相关问答