• 回答数

    5

  • 浏览数

    346

snake20001981
首页 > 英语培训 > 满量程的英文

5个回答 默认排序
  • 默认排序
  • 按时间排序

心菲殿下

已采纳

表示该设备的误差允许范围是±(0.25%×量程+最小分辨率。)

精度±(0.25%F.S.+1digit),精度指设备的误差允许范围,其中F.S.为英文full scale缩写,意即满量程的意思,digit中文意思为数字,是指仪表显示值最后一位,也叫最小分辨率。

精度计算举例:某温控仪表的精度为±(0.25%F.S.+1digit),T型热电偶输入范围为-199.9~400.0℃,那么满量程=400+199.9=599.9℃,因为显示值带有一位小数,所以最小分辨率为0.1℃,则1digit=0.1℃。

即,接T型热电偶时的此仪表的精度=±(0.25%F.S.+1digit)=±(0.25%×599.9+0.1)=1.59975≈1.6℃。

其他类型传感器输入时,仪表精度计算方法同上。

扩展资料

精度等级

在正常的使用条件下,仪表测量结果的准确程度叫仪表的准确度。引用误差越小,仪表的准确度越高,而引用误差与仪表的量程范围有关,所以在使用同一准确度的仪表时,往往采取压缩量程范围,以减小测量误差。

在工业测量中,为了便于表示仪表的质量,通常用准确度等级来表示仪表的准确程度。准确度等级就是最大引用误差去掉正、负号及百分号。准确度等级是衡量仪表质量优劣的重要指标之一。准确度等级习惯上称为精度等级。

表示方法及特性

精度常使用三种方式来表征。

1)最大误差占真实值的百分比,如测量误差3%;

2)最大误差,如测量精度±0.02mm;

3)误差正态分布,如误差0%~10%占比例65%,误差10%~20%占比例20%,误差20%~30%占10%,误差30%以上占5%。

比较以上三种表征方式,可以看出:

1.最大误差百分比方式简单直观。由于基于真实值,不具体。在不知道真实值的情况下,无法判读误差的具体大小。

2.最大误差方式简单直观,反应了误差的具体值,但是有片面性。

3.误差正态分布方式科学、全面、系统,但是表述较为复杂,所以反而不如前两种应用广泛。

合理配置精度

机械系统的总体精度由系统内各环节的精度构成,但是不同环节的精度对系统总体精度的影响程度不相同。在结构设计中,应为不同环节设置不同的精度,为敏感环节设置较高精度,这样可以通过较经济的方法获得较高的总体工作精度。

在机床主轴结构设计中,提高主轴前端的旋转精度是重要的设计目标。主轴前支点轴承和主轴后支点轴承的精度都会影响主轴前端的旋转精度,但影响的程度不同。由图1可见,前支点的误差对主轴前端精度的影响较大。所以在主轴结构设计中,通常为前支点设置具有较高精度的轴承。

满量程的英文

337 评论(12)

静香陈陈

电子学 英文2007-11-01 上午 09:28AC(alternating current) 交流(电)A/D(analog to digital) 模拟/数字转换ADC(analog to digital convertor) 模拟/数字转换器ADM(adaptive delta modulation) 自适应增量调制ADPCM(adaptive differential pulse code modulation) 自适应差分脉冲编码调制ALU(arithmetic logic unit) 算术逻辑单元ASCII(American standard code for information interchange) 美国信息交换标准码AV(audio visual) 声视,视听BCD(binary coded decimal) 二进制编码的十进制数BCR(bi-directional controlled rectifier)双向晶闸管 BCR(buffer courtier reset) 缓冲计数器BZ(buzzer) 蜂鸣器,蜂音器C(capacitance,capacitor) 电容量,电容器CATV(cable television) 电缆电视CCD(charge-coupled device) 电荷耦合器件CCTV(closed-circuit television) 闭路电视CMOS(complementary) 互补MOSCPU(central processing unit)中央处理单元CS(control signal) 控制信号D(diode) 二极管DAST(direct analog store technology) 直接模拟存储技术DC(direct current) 直流DIP(dual in-line package) 双列直插封装 字串7DP(dial pulse) 拨号脉冲DRAM(dynamic random access memory) 动态随机存储器DTL(diode-transistor logic) 二极管晶体管逻辑DUT(device under test) 被测器件DVM(digital voltmeter) 数字电压表ECG(electrocardiograph) 心电图ECL(emitter coupled logic) 射极耦合逻辑EDI(electronic data interchange) 电子数据交换EIA(Electronic Industries Association) 电子工业联合会EOC(end of conversion) 转换结束EPROM(erasable programmable read only memory) 可擦可编程只读存储器EEPROM(electrically EPROM) 电可擦可编程只读存储器ESD(electro-static discharge) 静电放电 FET(field-effect transistor) 场效应晶体管FS(full scale) 满量程F/V(frequency to voltage convertor) 频率/电压转换FM(frequency modulation) 调频FSK(frequency shift keying) 频移键控FSM(field strength meter) 场强计FST(fast switching shyster) 快速晶闸管FT(fixed time) 固定时间FU(fuse unit) 保险丝装置FWD(forward) 正向的GAL(generic array logic) 通用阵列逻辑GND(ground) 接地,地线GTO(Sate turn off thruster) 门极可关断晶体管 字串2 HART(highway addressable remote transducer) 可寻址远程传感器数据公路HCMOS(high density COMS) 高密度互补金属氧化物半导体(器件)HF(high frequency) 高频HTL(high threshold logic) 高阈值逻辑电路HTS(heat temperature sensor) 热温度传感器IC(integrated circuit) 集成电路ID(international data) 国际数据IGBT(insulated gate bipolar transistor) 绝缘栅双极型晶体管IGFET(insulated gate field effect transistor) 绝缘栅场效应晶体管I/O(input/output) 输入/输出I/V(current to voltage convertor) 电流-电压变换器IPM(incidental phase modulation) 附带的相位调制IPM(intelligent power module) 智能功率模块IR(infrared radiation) 红外辐射IRQ(interrupt request) 中断请求JFET(junction field effect transistor) 结型场效应晶体管LAS(light activated switch)光敏开关LASCS(light activated silicon controlled switch) 光控可控硅开关LCD(liquid crystal display) 液晶显示器LDR(light dependent resistor) 光敏电阻LED(light emitting diode) 发光二极管LRC(longitudinal redundancy check) 纵向冗余(码)校验 字串2LSB(least significant bit) 最低有效位LSI(1arge scale integration) 大规模集成电路M(motor) 电动机MCT(MOS controlled gyrator) 场控晶闸管MIC(microphone) 话筒,微音器,麦克风min(minute) 分MOS(metal oxide semiconductor)金属氧化物半导体MOSFET(metal oxide semiconductor FET) 金属氧化物半导体场效应晶体管N(negative) 负NMOS(N-channel metal oxide semiconductor FET) N沟道MOSFETNTC(negative temperature coefficient) 负温度系数OC(over current) 过电流OCB(overload circuit breaker) 过载断路器OCS(optical communication system) 光通讯系统OR(type of logic circuit) 或逻辑电路OV(over voltage) 过电压P(pressure) 压力FAM(pulse amplitude modulation) 脉冲幅度调制PC(pulse code) 脉冲码PCM(pulse code modulation) 脉冲编码调制PDM(pulse duration modulation) 脉冲宽度调制PF(power factor) 功率因数PFM(pulse frequency modulation) 脉冲频率调制PG(pulse generator) 脉冲发生器PGM(programmable) 编程信号PI(proportional-integral(controller)) 比例积分(控制器) 字串9PID(proportional-integral-differential(controller))比例积分微分(控制器)PIN(positive intrinsic-negative) 光电二极管PIO(parallel input output) 并行输入输出PLD(phase-locked detector) 同相检波PLD(phase-locked discriminator) 锁相解调器PLL(phase-locked loop) 锁相环路PMOS(P-channel metal oxide semiconductor FET) P沟道MOSFETP-P(peak-to-peak) 峰--峰PPM(pulse phase modulation) 脉冲相位洲制PRD(piezoelectric radiation detector) 热电辐射控测器PROM(programmable read only memory) 可编只读程存储器PRT(platinum resistance thermometer) 铂电阻温度计PRT(pulse recurrent time) 脉冲周期时间PUT(programmable unijunction transistor) 可编程单结晶体管PWM(pulse width modulation) 脉宽调制R(resistance,resistor) 电阻,电阻器RAM(random access memory) 随机存储器RCT(reverse conducting thyristor) 逆导晶闸管REF(reference) 参考,基准REV(reverse) 反转R/F(radio frequency) 射频RGB(red/green/blue) 红绿蓝ROM(read only memory) 只读存储器RP(resistance potentiometer) 电位器 字串3 RST(reset) 复位信号RT(resistor with inherent variability dependent) 热敏电阻RTD(resistance temperature detector) 电阻温度传感器RTL(resistor transistor logic) 电阻晶体管逻辑(电路)RV(resistor with inherent variability dependent on the voltage) 压敏电阻器SA(switching assembly) 开关组件SBS(silicon bi-directional switch) 硅双向开关,双向硅开关SCR(silicon controlled rectifier) 可控硅整流器SCS(safety control switch) 安全控制开关SCS(silicon controlled switch) 可控硅开关SCS(speed control system) 速度控制系统SCS(supply control system) 电源控制系统SG(spark gap) 放电器SIT(static induction transformer) 静电感应晶体管SITH(static induction thyristor) 静电感应晶闸管SP(shift pulse) 移位脉冲SPI(serial peripheral interface) 串行外围接口SR(sample realy,saturable reactor) 取样继电器,饱和电抗器SR(silicon rectifier) 硅整流器SRAM(static random access memory) 静态随机存储器SSR(solid-state relay) 固体继电器SSR(switching select repeater) 中断器开关选择器 字串8SSS(silicon symmetrical switch) 硅对称开关,双向可控硅SSW(synchro-switch) 同步开关ST(start) 启动ST(starter) 启动器STB(strobe) 闸门,选通脉冲T(transistor) 晶体管,晶闸管TACH(tachometer) 转速计,转速表TP(temperature probe) 温度传感器TRIAC(triodes AC switch) 三极管交流开关TTL(transistor-transistor logic) 晶体管一晶体管逻辑TV(television) 电视UART(universal asynchronous receiver transmitter) 通用异步收发器VCO(voltage controlled oscillator) 压控振荡器VD(video decoders) 视频译码器VDR(voltage dependent resistor) 压敏电阻VF(video frequency) 视频V/F(voltage-to-frequency) 电压/频率转换V/I(voltage to current convertor) 电压-电流变换器VM(voltmeter) 电压表VS(vacuum switch) 电子开关VT(visual telephone) 电视电话VT(video terminal) 视频终端

136 评论(11)

张小小晴晴

±(0.25%F.S.+1digit),其中F.S.为英文full scale缩写,意即满量程的意思,digit中文意思为数字,是指仪表显示值最后一位,也叫最小分辨率。 精度计算举例:某温控仪表的精度为±(0.25%F.S.+1digit),T型热电偶输入范围为-199.9~400.0℃,那么满量程=400+199.9=599.9℃,因为显示值带有一位小数,所以最小分辨率为0.1℃,则1digit=0.1℃。 即,接T型热电偶时的此仪表的精度=±(0.25%F.S.+1digit)=±(0.25%×599.9+0.1)=1.59975≈1.6℃。 其他类型传感器输入时,仪表精度计算方法同上。其他仪表精度算法与与此类似。

296 评论(15)

心无车马喧

之前我们培训时学过,不过忘记了。建议你百度一下。

272 评论(9)

壬生京三郎

±1%FS的意思精度是满量程的±1%,是个稳定的值。FS是英文Full SCAL(满量程)的简写。*******************************您好,答案已经给出,请您浏览一遍有什么不懂的地方欢迎回复我!如果满意请及时点击【采纳回答】按钮或者客户端的朋友在右上角评价点【满意】您的采纳,是我答题的动力也同时给您带来知识和财富值***************************************************

101 评论(15)

相关问答