期刊问答网 论文发表 期刊发表 期刊问答
  • 回答数

    2

  • 浏览数

    107

lyjhhxn0891
首页 > 期刊问答网 > 期刊问答 > 电气论文英文版

2个回答 默认排序1
  • 默认排序
  • 按时间排序

wgyyab

已采纳
是这个样子的吗?如有需要回复我 水 泥 科 技SCI CE jD 佃C )I JC)GY OF CE 任NT1 概述一起变压器差动保护误动作的案例分析孙 峻(合肥水泥研究设计院 230051)智利拉法基二十万吨水泥粉磨生产线是我院首个在美洲地区开展的EP项目,此项目的成败关系到我院能否开拓美洲市场,是我院实施美洲开发战略的关键。此项目从开始的设计到设备的选型都是国内最先进的,技术含量也是最高的。为此我院的工程技术人员付出了艰辛的汗水,但是现场电气方面还是出现了一些技术问题。我院工程技术人员非常重视出现的问题,没有丝毫懈怠,在智利技术人员的大力配合下和我院的工程技术人员努力下,电气问题终于得到圆满的解决,受到了业主的好评。笔者在此仅将智利拉法基现场出现的变压器微机差动保护误动作问题例举出来,加以技术分析,谨供大家参考。2 电气故障的现象智利拉法基二十万吨水泥粉磨生产线的供电是采取23/6.6kV& 23/0.4kV两路供电方式,两台主变的技术参数见表1、表2。表1 1#主变变压器型号 S11一ⅣB一3150/23有载调压 23±2x2.5变压器接线方式 Dynl1变压器容量 3150t电压比 23/6.6kV表2 2#主变变压器型号 Sl1一MB一2000/23有载调压 23±2x2.5变压器接线方式 Dynl1变压器容量 2000kI电压比 23/0.4kV主变的主保护是微机差动保护(型号:R圈1543),R 43型号的微机综保是ABB公司近期新推向世面的一种新型综保,其功能非常强大,自带运行软件和程序的自主编程,为用户提供了方便。经过半年的安装于2008年1月20日试投入运行,两台主变空载运行一切正常。但是当两台主变在带上负荷生产以后,两台主变高压侧相继出现跳闸现象,ABB微机综保显示微机差动保护动作,显然这样将严重影响全厂的生产,这一问题必须尽快得到解决。3 故障的检查步骤和技术分析(1)首先检查高低压侧电流互感器相序是否一致,在电源的相序是正序的情况下,只要合理的选择变比以及微机相位补偿,流过差动电流是很小的,而负序的情况就不一样了,高压侧电流互感器副边输出的电流和和低压侧电流互感器副边输出的电流相位相差60。,因此就能引起差动保护误动作,但是经过现场认真的检查电源的相序是正确的。(2)检查变压器两端的电流互感器的变比和综保的保护值是否相匹配以及重新校验且核算保护定一35 —2008.N93水 泥 科 技SCIENCEAND )IoGY OFC值,没有发现任何问题。(3)检查电流互感器二次侧是否断线,原因是在变压器有一定负荷时,若电流互感器二次回路断线,将可能造成差动保护起动元件、差动元件动作,从而引起差动保护误动作。检查结果是没有发现上述的问题。(4)接着,所有的技术人员开始怀疑变压器内部是否有故障,经过对两台主变的性能测试和出厂值的校验,检测的数据和变压器出厂时几乎一样。(5)根据ABB(RKI'543)的微机综保技术资料,检查ABB(R踊43)的微机综保的接线端子(变压器两侧电流互感器接到综保的电流接线端子位置是否正确),发现变压器两侧电流互感器与综保接线有误,厂家把变压器高压侧的电流互感器和低压侧的电流互感器的电流信号接到综保的位置接反了,在接线调整正确以后,发现差动保护跳闸的现象依然存在。此时,现场的问题显得扑朔迷离,但是中智双方工程技术人员没有泄气,看图纸、查资料,终于找到了问题的痼疾。原来是互感器的二次侧同极性端子接错导致差动保护误动作,因为这样的接线方式会导致两侧电流互感器的二次电流在差动回路中方向相同,微机综保流过的电流为两相电流之和,在变压器空载运行时故障一般不容易反映不出来,只有当变压器带上一定负荷时,差动保护就会动作。重新接线后两台变压器带负荷运行一切正常。图1这样,在双方技术人员的艰苦努力下,这一起变一36 一压器差动保护误动作终于水落石出,故障得到了圆满的解决,而萦绕在工程技术人员心头久久不能散去的迷雾也渐渐消融,化作工程圆满完成的一场喜雨。图1是差动保护的正确和错误的接线。4 体会与建议4.1 故障的分析与排除通过对差动保护误动作故障的分析和故障排除整个过程,阐述了一些正常运行时(系统无故障及无冲击)差动保护误动作的原因,但是除了上述的原因还有一些因素也可能导致变压器正常运行时差动保护误动作,主要现象为:(1)电流互感器二次回路中接线端子螺丝松动,使二次回路连线接触不良或短时开路。(2)电流互感器二次回路中一相接触不良,在接触不良处产生电弧造成单相接地或两相之间的接地(电流互感器二次回路短路)。(3)电流互感器二次回路电缆芯线外层绝缘损坏或损伤,在运行中由于震动造成接地短路。(4)差动电流互感器二次回路多点接地,而且接地点不在同一处,造成接地点之间电位差太大,使差动元件产生差流导致差动误动作(雷雨季节较多)。4.2 建议为了提高差动保护的动作可靠性应做好以下工作:(1)严格检查电流互感器的极性;如果电流互感器极性在接线时接错了,那么将它用在保护回路中,将会引起保护的误动作,如果用在仪表测量回路中,会影响计量的准确性。(2)严防电流互感器二次回路接触不良和开路的现象;加强对差动回路差流运行监视以及对保护装置的维护。在变压器和保护装置安装调试以后,应仔细的检查电流互感器二次回路,拧紧二次回路接线端子螺丝并且用弹簧垫进行加固。(3)严格执行规范要求;所有电气上有连接的差动电流互感器二次回路只能有一个公共接地点,并且该接地点位置应在保护盘上。(4)确保差动电流互感器二次电缆芯线之间和各芯线对地绝缘;对于变压器初次运行和高压设备检修后的运行,要用1000V绝缘电阻表测量电流互感器二次电缆芯线之间和各芯线对地绝缘,使之符合电气规程的要求;另外选择电流互感器二次电缆的截面应不小于4mm 。

电气论文英文版

226 评论(10)

DearLuo

Along with the our country economic development rapid development, the lives of the people level unceasing enhancement, the city uses to be day by day anxious, urges the building to face the direction is This kind of high level civil construction repair needed materials and the way also more hasten the diversification, and along with uses electricity the load and coal gas consumption quantity enlarging, proposed to the fire auto-alarm system design is higher, a stricter In order to guarantee the people life and property the security, the fire auto-alarm system design has become in the high level civil construction design one of most important design Presently based on the author fire of auto-alarm system design overseeing work in the high level civil building experience, proposed in present national related standard and standard unclear true detail shallow opinion, by for the colleagues to discuss and to point out First, design basis The fire auto-alarm system design is a specialized very strong technology work, at the same time also has the very strong policy- Therefore, first should be clear about the following design basis: 1st, must grasp the architectural design fire protection standard, the system design standard, the equipment manufacture standard, the installment construction approval standard and the administration laws and regulations and so on five big aspects fire laws and regulations, and in practical understanding present country related standard and standard positive word: "Must", "be supposed", "to be suitable", "may" and the reverse side word: "Strictly prohibits", "should not", "not have", "not to be suitable" the 2nd, must aim at high level civil building function, use and the protection object fire protection rank, earnestly carries out the present national related standard and the standard, earnestly treats the public security fire prevention surveillance department the examination and approval Second, fire auto-alarm system equipment establishmentFire detector establishmentOpens wide either the seal or the stair hall should alone divide the search coverage, and each 2 ~ 3 establish a fire The first room (including guards against in front of smoke stair hall in front of room, fire elevator room, fire elevator with guards against the front room which smoke stair hall comes in handy) and the aisle should distinguish alone to divide the search coverage, specially front the room and the lift well, the scattered stair hall and the aisle are interlinked, has time the fire haze to be easier to gather or to flow, is the personnel disperses which saves goal with the fire prevention, therefore should install the fire Regarding common elevator in front of room although is not the personnel disperses , but this front room and the lift well are interlinked, has time the fire haze to be also easy to gather or to flow, suitably alone divides the search coverage and installs the fire The electric cable shaft therefore is easy to form pulls out the smoke inflammation the channel; Has when the fire the fire intensity not easily extends along the electric cable burns, for this, "the high level civil construction design fire protection standard" and "the civil construction electricity design standard" separately proposes the detailed specific stipulation in the construction and in the electric wire or on the electric cable But considered implements specifically the difficulty and the present situation, the electric cable shaft installs the fire detector is extremely essential, and coordinates the shaft the fire protection separation request, each 2 ~ 3 or each level The elevator machine room should install the fire detector, its elevator is the important vertical transportation vehicle; Its two elevator machine room has has the fire risk; Its three lift well existence essential opens the hole, like the level gate opens between the hole, the air vent, the between permanence opens the hole with the elevator machine room or the pulley and so on; Its four when has the fire, the lift well often becomes the fire intensity spread the channel, is easy to threaten the elevator machine room the Therefore, the elevator machine room establishes the fire detector is necessary, crown of also suitable establishment fire detector lift 2nd, the manual fire reports to the police the button establishment(Including guards against in front of smoke stair hall in view of various floors front room in front of room, fire elevator room, fire elevator with guards against which smoke stair hall to come in handy the front room) is has when the fire the personnel to disperse which saves goal with fire prevention, should report to the police the button first choice spot as the establishment manual In addition, the room also should establish the manual fire to the common elevator in front of to report to the police the In the public active place (including hall, hall, dining room, multi-purpose hall and so on) and the main thoroughfare and so on place, the personnel very is all centralized, and mainly disperses the Therefore should report to the police the button in these public active places main access establishment manual fires; The manual fire establishes which in the main thoroughfare reports to the police the button to guarantee "to a manual fire which most is close to reports to the police the button distance from a fire protection district any position not to be supposed to be bigger than 30 meters"3rd, the fire emergency broadcasts the speaker the establishmentThe aisle, the hall, the dining room and so on the public place personnel very are all centralized, and mainly disperses the Therefore should press in these public places "to a recent speaker distance is not bigger than 25 meters from a fire protection district any spot" and "in the aisle last should not be bigger than 5 meters the speaker to the aisle terminal distance" the establishment fire emergency to broadcast the speaker; Next also should establish the fire in the public bathroom place emergency to broadcast the The first room (including guards against in front of smoke stair hall in front of room, fire elevator room, fire elevator with guards against which smoke stair hall to come in handy the front room) is has when the fire the personnel to disperse which saves goal with fire prevention, also has the fire door separation and the sounds of people is confused and noisy, therefore should establish the fire emergency to broadcast the In front of the common elevator the room also should establish the fire emergency to broadcast the Disperses the stair hall also is has when the fire the personnel to disperse which saves goal with the fire prevention, also the sounds of people are confused and noisy, therefore should establish the fire emergency to broadcast the speaker, by favors the fire emergency broadcast to disperse the 4th, fire alarm installment establishmentThe establishment fire emergency broadcast fire auto-alarm system, the author thought also should install the fire alarm installment, but its control procedure should be: The alarm apparatus should confirm after the fire, uses manual or the automatic control mode unification to the fire correlation region transmission warning, stops the alarm apparatus work in the stipulation time, the rapid linkage fire emergency broadcast and broadcasts to the people disperses the The fire alarm installment establishment position, the author thought should report to the police the button position with the manual fire to be same, its wall surface installment should for be apart from the ground 8 meters highly5th, fire special use telephone establishmentInstalls the fire special use telephone extension telephone, should be located the engine room which related also some people is on duty frequently with the fire linkage control (including fire water plant, spare electricity generation engine room, matches substation, mainly ventilates with air conditioning engine room, discharges fume engine room, fire prevention elevator machine room and other), the fire fighting control system operates the equipment place or the control room, the fire duty officers observation room, the security manages spot and so on public Sedan of theater box the fire elevator and in the ordinary elevator all should suppose the special use telephone, requests the elevator machine room and the elevator sedan theater box, the elevator machine room and the fire control room, the elevator sedan theater box and the fire control room and so on three compositions is reliable to speaks the correspondence telephone Usually in fire control room; The establishment elevator monitoring demonstration plate (including position indicator, direction indicating lamp, to speaks correspondence telephone, trouble lamp and so on), in order to carries on the necessity to the elevator running status which in the surveillance and the emergency case Is equipped with the manual fire to report to the police position and so on button, fire hydrant button also should install the fire special use telephone Third, fire linkage control 1st, the fire linkage control should include the control fire pump to open, to stop, also should demonstrate opens pumps the button the position and the fire pump work and the When the fire hydrant is equipped with the fire hydrant button, its electric installation work spot also should demonstrate the fire pump the working mode active status (namely establishment fire pump work indicating lamp) 2nd, the fire linkage control should include the control spraying of water and the water atomization fire fighting system opens, stops, also should demonstrate the fire pump the work and the malfunction and the fluent display, reports to the police the valve, the safety signal valve working mode active In addition, to the basin, the water tank water level also should carry on the demonstration monitor; In order to prevent the overhaul signal valve is shut down, the author thought should use the belt electric signal the control signal valve by to demonstrate it opens the 3rd, the fire linkage control other controls and the demonstration function, should carry out the present national related standard and the standard specific Fourth, fire auto-alarm system wiringIn order to prevent the fire occurs when the fire control, the correspondence and the warning line severance, causes the fire fighting work to be unable to carry on, creates the bigger economic loss; Also for the suppression electronmagetic interference (for example transformer, electric motor, electric cable and so on) the influence which produces to the fire auto-alarm The fire auto-alarm system transmission line and the fire control, the correspondence and the warning line should use the being flame-resistant electric cable, and should use the metal tube or the enclosed metal trunking The fire manual positive governing installment line should use the fireproof electric cable, its electric cable also should use the metal tube or the enclosed metal trunking Uses Ming Fushi, should takes the fire protection protective measures on the metal tube or the enclosed metal Fifth, concluding remarkThe author rests on the concrete project to implement the experience, elaborated the design basis, fire auto-alarm design actual problem and so on system equipment establishment, fire linkage control and its wiring pulls out some shallow opinions, its goal is enhances the fire auto-alarm system the design quality, discovered early and the notification fire, prevented and reduces the fire to harm, by protects the person and the property 随着我国经济发展快速发展,人民生活的水平不断提高,城市使用是每天着急,敦促建设面临着发展的方向。这种高层次的民间建筑维修所需的材料和方式也更加多样化加快,而且随着使用电力负荷和煤气消费量扩大,提议消防自动报警系统设计较高,更严格的要求。为了保证人民生命和财产的安全,消防自动报警系统的设计已经成为在高级别民间建筑设计的一个最重要的设计内容。目前的基础上撰文火灾自动报警系统设计监督工作的高层次的民间建设的经验,建议在目前国家相关标准和标准不清楚真正详细浅见解,为同事们的讨论,并指出错误。 首先,设计依据 火灾自动报警系统的设计是一家专业非常强的技术工作,同时还具有很强的政策性。因此,首先应明确以下设计依据: 第一,必须紧紧抓住的建筑设计防火标准,该系统的设计标准,标准的设备制造,安装施工审批标准和管理的法律和规章等五大方面的消防法律法规,并在实际了解国家有关本标准和标准积极字: “必须” , “必须假定” , “不适合” , “可能”和反面词: “严格禁止” , “不应该” , “没有” , “不适合“的含义。 第二,必须着眼于高层次的民间建筑的功能,利用和保护对象的防火等级,认真开展本标准和国家有关标准,认真对待公安防火监督部门的审批意见。 其次,火灾自动报警系统设备的建立 建立火灾探测器 要么全打开的印章或楼梯大厅应单独划分搜索范围,每个2 〜 3建立火灾探测器。 第一个房间(包括防前面的烟雾大厅楼梯前室,消防电梯间,消防电梯防前面房间烟雾楼梯大会堂来用场)和过道应区分单独划分搜索范围,特别是前面的房间,以及电梯,分散楼梯大厅和走道都是相互关联的,有时间的火灾烟雾比较容易收集或流动,是人员分散保存目标与防火,因此,应该安装火警探测器。关于共同电梯前室虽然不是人员分散,而且这方面的空间和良好的电梯是相互关联的,有时间的火灾烟雾也很容易被收集或流动,适当地划分为单独的搜索覆盖面和安装消防探测器。 电缆轴因此很容易形成掏出烟炎症渠道,拥有火灾时的火强度不容易延伸沿电缆燃烧,为此, “高级别民间建筑设计防火标准”和“民用建筑电气设计标准“分别提出了详细具体的规定,在建筑和在电线或电缆塑造。但认为具体实施的难度和目前的情况下,电缆竖井安装了火灾探测器是非常必要的,坐标轴的防火分隔要求,每2 〜 3或每一级安装。 电梯机房应安装火灾探测器,它的电梯是重要的垂直交通工具,其两个电梯机房已具有火灾危险性,其存在的三个基本解除以及打开洞,像打开闸门的水平之间的球洞,在气孔,持久的关系打开了洞与电梯机房或滑轮等,其时,有四个火,升降机以及往往成为火灾强度传播渠道,很容易危及电梯机房设施。因此,电梯机房建立了火灾探测器是必要的,也适用于皇冠建立火灾探测器举井。 2 ,手动火警报警按钮建立 (包括防前面的烟雾楼梯大厅鉴于各层前房间前面的房间,消防电梯间,消防电梯防这些烟雾楼梯大会堂派上用场前室)是有火灾时人员驱散节省目标,防火,应立即向警方举报的按钮,首选地点设立手动火警。此外,该室也应建立防火手册的共同电梯前,向警方报案的按钮。 在公共活动场所(包括会堂,礼堂,餐厅,多功能厅等)和主要通道等场所,是所有工作人员非常集中,主要是分散的渠道。因此,应立即向警方举报的按钮,在这些公共活动场所主要通道设立手册火灾;该手册规定的火灾中的主要通道报警按钮,以保证“ ,以手动火警最接近报警按钮距离防火区的任何位置不应该超过30米。 “ 第三,消防紧急广播喇叭建立 走道,大厅,餐厅等公共场所的工作人员都非常集中,主要是分散的渠道。因此,应该按这些公共场所的“最近的一项发言距离不超过25米的防火保护区的任何位置”和“在走道上不应大于十二点五米扬声器的过道末端距离”建立消防应急广播喇叭;下一步还应当建立消防在公共浴室的地方紧急广播喇叭。 第一个房间(包括防前面的烟雾大厅楼梯前室,消防电梯间,消防电梯防这些烟雾楼梯大会堂派上用场前室)是有火灾时的人员驱散节省目标与防火,也有分离和防火门的声音,人民的混乱和嘈杂,因此,应建立消防应急广播喇叭。在前面的共同电梯房也应建立消防应急广播喇叭。分散大厅楼梯也已经火灾时的人员驱散节省目标与防火,也是人民的声音和嘈杂的混淆,因此应建立消防应急广播喇叭,由主张消防紧急广播驱散指令。 第四,建立火灾报警装置 建立消防应急广播火灾自动报警系统,笔者认为还应该安装消防报警装置,但它的控制程序应该是:该报警器应确认火灾后,利用手动或自动控制模式统一消防相关区域传输预警,报警器停止工作时间的规定,迅速联系消防应急广播和电视节目,并且分散了人们的指示。 火警警报装置建立的立场,笔者认为应该向警方报案的按钮位置的手动火警是相同的,它的墙面安装应为距地面8米高度 第五,消防专用电话设立 安装消防专用电话分机电话,应设机房其中也涉及一些人是在工作地点经常与消防联动控制(包括消防给水设备,备件发电机房,火柴变电站,主要ventilates空调引擎室,排放烟气轮机室,防火电梯机房及其他) ,消防控制系统的经营场所或设备的控制室,消防责任人员观察室,现场的安全管理等公共空间。轿车的影院中消防电梯和普通电梯应假设所有使用的特殊电话,请电梯机房和电梯轿车影院中,电梯机房及消防控制室,电梯轿车影院方块和消防控制室等三个成分是可靠的讲通信电话系统。通常在消防控制室;建立电梯监测演示板(包括位置指示器,显示方向灯,以讲信函电话,麻烦灯等) ,以进行必要的电梯在运行状态的监视和紧急情况下的控制。 配备了手动火警报警位置等按钮,消火栓按钮,还应该安装消防专用电话插座。 第三,消防联动控制 第一,消防联动控制应包括控制消防泵开启,停止,也应表现出的按钮,打开泵的位置和消防泵的工作和故障。当消火栓设有消火栓按钮时,其电气安装工程现场也应表现出的消防泵的工作模式有效状态(即建立消防泵工作表明灯) 。 第二,消防联动控制应包括控制喷洒水和水雾化灭火系统打开,停止,也应表现出的消防泵的工作和故障和流利显示,报警阀,安全信号阀工作模式积极的地位。此外,该盆地,水箱水位也应进行示范监测;为了防止检修信号阀关闭,作者认为应该使用带电信号控制信号阀证明它打开条件。 第三,消防联动控制其他控制和示范作用,应进行本标准和国家有关标准的具体规定。 第四,火灾自动报警系统布线 为了防止火灾发生时,消防控制,通信和警戒线遣散,使灭火工作无法进行,造成了更大的经济损失,也为抑制electronmagetic干扰(例如变压器,电电机,电缆等)的影响而产生的火灾自动报警系统。火灾自动报警系统的输电线路和消防控制,通信和预警线应使用被阻燃电缆,并应使用金属管或封闭式金属线槽保护。消防手册积极理事分期付款行应使用防火电缆,其电缆也应使用金属管或封闭式金属线槽保护。使用明复,应采取防火保护措施的金属管或封闭金属Fifth ,结论备注 作者取决于具体的项目实施经验,阐述了设计依据,火灾自动报警设计和实际问题,以便建立系统设备,消防联动控制及其接线拿出一些肤浅的意见,其目的是增强了火灾自动报警系统的设计质量,早期发现,并通知消防,预防和减少火灾危害,通过保护个人和财产安全。
152 评论(9)

相关问答